| 193 | 0 | 12 |
| 下载次数 | 被引频次 | 阅读次数 |
【目的】抽水蓄能机组安全稳定运行和轴系无共振发生是抽水蓄能电站有效支撑新型电力系统调节需求的重要保证。【方法】针对抽水蓄能电站中机组轴系选取不同结构单元开展模态特性研究，基于有限元方法，选取400.0～3 000.0 r/min的6种旋转速度工况，对比分析独立水轮机转轮、水轮机转轮-轴、水轮机转轮-轴-发电机转子三种结构单元的6阶激振频率与振型。【结果】结果表明：对于不同结构单元，部件的固有频率与振型均不相同，但不同的结构下亦会出现相同的振型；独立水轮机转轮结构的6阶固有频率最大，且没有出现临界转速；转轮-轴-转子结构的6阶固有频率最小，且在前2阶模态中出现临界转速。对水泵水轮机旋转部件进行模态分析时，第1阶和第2阶模态均出现了临界转速，大小分别为1 387.1 r/min和2 164.0 r/min;而仅考虑水泵水轮机转轮和轴部件下，只在第1阶出现了临界转速，转速大小和转轮-轴-发电机转子的第2阶临界转速相同，为2 164.0 r/min,且对应的振型和固有频率均相同；只考虑水泵水轮机转轮部件时没有出现临界转速。【结论】在对水泵水轮机旋转部件进行模态分析时，考虑发电机转子与轴部件更能精确地发现旋转部件的临界转速并预测共振频率与模态振型，有利于避免机组共振的情况出现。研究成果为抽水蓄能机组轴系结构设计提供了理论依据和工程实践支撑。
Abstract：[Objective]The safe and stable operation of pumped storage units and the avoidance of shafting resonance are essential for pumped storage power stations to effectively meet the regulation demands of new-type power systems.[Methods]Different structural units were selected to study the modal characteristics of the unit shafting in the pumped storage power stations. Based on the finite element method, six rotational speed conditions of 400.0～3 000.0 r/min were selected to conduct a comparative analysis of the sixth-order excitation frequencies and vibration modes of three structural units: independent turbine runner, turbine runner-shaft, and turbine runner-shaft-generator rotor.[Results]The result showed that for different structural units, the natural frequencies and vibration modes of the components were different, though identical vibration modes could occur under different structures. The independent turbine runner structure had the highest sixth-order natural frequency, with no critical speed observed. The runner-shaft-rotor structure had the lowest sixth-order natural frequency, with critical speeds occurring in the first two modes. In the modal analysis of the rotating components of the pump turbine, critical speeds were observed at the 1st and 2nd modes, with speeds of 1 387.1 r/min and 2 164 r/min, respectively. However, when only the runner and shaft components of the pump turbine were considered, the critical speed was observed only at the 1st mode, with a speed identical to the 2nd mode critical speed of the runner-shaft-generator rotor, which was 2 164.0 r/min. The corresponding vibration mode and natural frequency were identical. No critical speed was observed when considering only the runner components of pump turbine.[Conclusion]Therefore, in the modal analysis of the rotating components of the pump turbine, considering the generator rotor and shaft components can more accurately identify the critical speeds of the rotating components and predict the resonance frequencies and vibration modes, which is beneficial for avoiding resonance in the unit. The research findings provide a theoretical basis and engineering support for the design of shafting structure in pumped storage units.
[1] 史广泰，杨茜，刘宗库，等.混流式水轮机转轮模态计算及振动特性分析[J].西华大学学报(自然科学版),2019,38(6):1-6.SHI G T,YANG X,LIU Z K,et al.Modal calculation and vibration characteristics analysis of francis turbine runner[J].Journal of Xihua University (Natural Science Edition),2019,38(6):1-6.
[2] 张涛，孔令华，谭信，等.水泵水轮机导水机构与转轮动应力特性分析[J].中国农村水利水电，2024(1):207-216.ZHANG T,KONG L H,TAN X,et al.An analysis of the dynamic stress characteristics of the distributor and runner in the pump-turbine[J].China Rural Water and Hydropower,2024(1):207-216.
[3] 桂中华，夏翔，王薇，等.水泵水轮机启动过程转轮动应力分析[J].农业机械学报，2021,52(12):153-161.GUI Z H,XIA X,WANG W,et al.Dynamic stress analysis of pump-turbine runner during start-up[J].Transactions of the Chinese Society for Agricultural Machinery,2021,52(12):153-161.
[4] 姜爱军，孔令华，张涛，等.某大型抽水蓄能电站水泵水轮机转轮强度及模态分析[J].水电与抽水蓄能，2023,9(1):19-24.JIANG A J,KONG L H,ZHANG T,et al.Strength and modal analysis of pump turbine runner in a large pumped storage power station[J].Hydropower and Pumped Storage,2023,9(1):19-24.
[5] 范洋铭，何启源，王明坤，等.长短叶片转轮对振动改善的应用与研究[J].水利水电技术(中英文),2022,53(7):58-68.FAN Y M,HE Q Y,WANG M K,et al.Application and study on vibration improvement by runner with splitter blades[J].Water Resources and Hydropower Engineering,2022,53(7):58-68.
[6] 杨小龙，王超，陈志明，等.附加质量对水泵水轮机转轮模态特性的影响[J].水力发电学报，2021,40(9):78-85.YANG X L,WANG C,CHEN Z M,et al.Influence of added mass on modal characteristics of pump turbine runners[J].Journal of Hydroelectric Engineering,2021,40(9):78-85.
[7] 张金凤，宋海勤，张帆，等.带分流叶片水泵水轮机转子强度及模态分析[J].排灌机械工程学报，2021,39(10):981-986.ZHANG J F,SONG H Q,ZHANG F,et al.Analysis on rotor strength and mode of pump-turbine with splitter blades[J].Journal of Drainage and Irrigation Machinery Engineering,2021,39(10):981-986.
[8] 翟宇，李晓超，马夏敏，等.小水电尾水水轮机转轮优化研究[J].水利水电技术(中英文),2024,55(8):93-103.ZHAI Y,LI X C,MA X M,et al.Research of runner optimization of small hydropower tailrace turbine[J].Water Resources and Hydropower Engineering,2024,55(8):93-103.
[9] 李璘君，杨世伟，王远铭，等.混合式抽水蓄能电站水温影响研究[J].水利水电技术(中英文),2024,55(9):133-143.LI L J,YANG S W,WANG Y M,et al.Study on the effect of water temperature in a hybrid pumped storage power station[J].Water Resources and Hydropower Engineering,2024,55(9):133-143.
[10] HE L Y,ZHOU L J,AHN S H,et al.Evaluation of gap influence on the dynamic response behavior of pump-turbine runner[J].Engineering Computations,2019,36(2):491-508.
[11] EGUSQUIZA E,VALERO C,PRESAS A,et al.Analysis of the dynamic response of pump-turbine impellers.Influence of the rotor[J].Mechanical Systems and Signal Processing,2016,68/69:330-341.
[12] LIU D H,XIA X,YANG J,et al.Effect of boundary conditions on fluid-structure coupled modal analysis of runners[J].Journal of Marine Science and Engineering,2021,9(4):434.
[13] HU D Q,WANG W,WANG S H,et al.Study on the influence of gap water body on the modal characteristics of pump turbine runner[C]//IEEE.2021 3rd International Conference on Artificial Intelligence and Advanced Manufacture (AIAM).Mancheste:IEEE,2022:43-46.
[14] 徐瑞红，龙胜鹏，于凤荣，等.基于ANSYS水轮发电机组轴系临界转速及模态分析[J].云南水力发电，2020,36(2):103-106.XU R H,LONG S P,YU F R,et al.Critical speed and modal analysis of hydraulic generator set shafting based on ANSYS[J].Yunnan Water Power,2020,36(2):103-106.
[15] 彭悦蓉，赖喜德，张惟斌，等.导轴承系统对水电机组轴系特性影响分析[J].水力发电学报，2015,34(9):106-113.PENG Y R,LAI X D,ZHANG W B,et al.Analysis on impact of guide bearing system on characteristics of hydro turbine shaft system[J].Journal of Hydroelectric Engineering,2015,34(9):106-113.
[16] 邹佳杰，周大庆，郭俊勋，等.不同负荷工况水轮发电机组轴系振动特性研究[J].水电能源科学，2023,41(3):176-180.ZOU J J,ZHOU D Q,GUO J X,et al.Research on vibration characteristics of shafting system of hydroelectric generating set under different load conditions[J].Water Resources and Power,2023,41(3):176-180.
[17] 狄洪伟，莫亚波，张政，等.某250 MW抽水蓄能机组轴系振动特性分析[J].四川水力发电，2019,38(6):1-6.DI H W,MO Y B,ZHANG Z,et al.Analysis of the shafting vibration characteristics of a 250 MW pumped storage generator[J].Sichuan Hydropower,2019,38(6):1-6.
[18] NIU L T,SUN Q,MA C Y,et al.Research on modal analysis of rotor shaft system of hydro-generator[J].Journal of Physics:Conference Series,2020,1549(4):042084.
[19] WU W D,PANG J Y,LIU X Y,et al.Effect of unbalanced magnetic pull of generator rotor on the dynamic characteristics of a pump:Turbine rotor system[J].Water,2023,15(6):1120.
[20] LIU X Y,PANG J Y,LI L,et al.Comparative study on numerical calculation of modal characteristics of pump-turbine shaft system[J].Journal of Marine Science and Engineering,2023,11(11):2068.
[21] 孔令华，姜爱军，李向阳，等.水泵水轮机内部流态特性及预应力模态分析[J].人民长江，2023,54(9):151-159.KONG L H,JIANG A J,LI X Y,et al.Research on internal flow characteristics and prestress modal analysis of pump turbine[J].Yangtze River,2023,54(9):151-159.
[22] 岳志伟，郑源，阚阚，等.基于流固耦合的某抽水蓄能电站可逆式水轮机转轮强度和模态分析[J].水电能源科学，2017,35(2):181-184.YUE Z W,ZHENG Y,KAN K,et al.Modal analysis of reversible turbine runner strength for pumped storage power station based on fluid solid coupling[J].Water Resources and Power,2017,35(2):181-184.
[23] 何严希，周建中，马越，等.基于流固耦合的混流式转轮受力与振动特性分析[J].水电能源科学，2022,40(1):187-191.HE Y X,ZHOU J Z,MA Y,et al.Force and vibration analysis of francis turbine based on fluid solid coupling[J].Water Resources and Power,2022,40(1):187-191.
[24] 杜康.反向发电工况下沙集站立式混流泵装置水动力特性及叶片水力激振特性研究[D].扬州：扬州大学，2023.DU K.Research on the Hydraulic Performance and Blade Hydraulic Vibration Characteristics of a Vertical Mixed-Flow Pump Unit under Reverse Power Generation Condition in Shaji Pumping Station[D].Yangzhou:Yangzhou University,2023.
[25] LIANG Q W,RODR■,et al.Modal response of hydraulic turbine runners[C]//International Association For Hydraulic Research.Proceedings of the 23rd IAHR Symposium on Hydraulic Machinery and Systems.Yokohama:International Association For Hydraulic Research,2006:1-9.
[26] 赵文鲁.水轮机转轮干湿模态振动特性分析[J].水利科技与经济，2016,22(8):32-33.ZHAO W L.Analysis on vibration characteristics of wet and dry modal of turbine runner[J].Water Conservancy Science and Technology and Economy,2016,22(8):32-33.
[27] LIANG Q W,RODR■,et al.Numerical simulation of fluid added mass effect on a francis turbine runner[J].Computers & Fluids,2007,36(6):1106-1118.
[28] 张士昂，李昊，张蓓，等.基于声固耦合算法的贯流式水轮机轴系振动特性研究[J].机械设计，2023,40(S1):105-109.ZHANG S A,LI H,ZHANG B,et al.Vibration characteristics of tubular turbine shafting based on acousto-structure coupling algorithm [J].Journal of Mechanical Design,2023,40(S1):105-109.
[29] MAO Z Y,TAO R,CHEN F N,et al.Investigation of the starting-up axial hydraulic force and structure characteristics of pump turbine in pump mode[J].Journal of Marine Science and Engineering,2021,9(2):158.
[30] 徐永.大型水轮发电机组轴系动力学建模与仿真分析[D].武汉：华中科技大学，2012.XU Y.Dynamic Modeling and Simulation Analysis of the Shaft System for Large Hydro-Turbine Generator Units[D].Wuhan:Huazhong University of Science and Technology,2012.
基本信息:
DOI：10.13928/j.cnki.wrahe.2025.11.013
中图分类号:TV743
引用信息:
[1]李晓波,段学友,贾斌,等.抽蓄机组轴系结构单元选取对模态分析的影响[J].水利水电技术(中英文),2025,56(11):168-178.DOI:10.13928/j.cnki.wrahe.2025.11.013.
基金信息:
内蒙古电力(集团)有限责任公司内蒙古电力科学研究院分公司自筹项目(2023-ZC-10); 国家自然科学基金项目(52379086); 江苏省创新支撑计划国际科技合作项目(BZ2023047)